NC Control of Cutting and Auto Cycle
The NC index control provides greater flexibility and expanded capabilities compared to a The controller enables the operator to specify the index home position – forward and clamped or at the index position and open. The controller also determines the speed of the index vise motion forward and reverse. It provides independent ramp cycles for the forward and rear traverse. The speed ramp up and down for moving the work piece is slower when it is positioning the work piece than when it is moving without work. This feature provides more accurate indexing of the work piece.
Smart Multiple Index
The machine control has the capability to make multiple full length index strokes until the length remaining to index is less than the full index stroke (15.8 in., 400mm.) the last index stroke is the remaining length.
Band Deviation Monitor ®
This patented cutting control device can reduce scrap by warning when the blade is no longer cutting within the operator’s settings for deviation. The allowable deviation limit is set by the operator independently for each direction. The digital deviation indicator will flash when the blade deviation exceeds either maximum. If the deviation continues to exceed the preset value the NC controller will stop the cutting, raise the saw head and display the exceeded deviation value.
Split Front Vise
The work holding vise is split so that it clamps the work piece on both sides of the cutting plane. This additional support in front of the cutting plane minimizes the burr on the cut pieces.
|Cutting Capacity||Round (Diameter)||1.18″-10″||30-250 mm|
|Rectangle (W x H)||10.6″ x 10″||270 x 250 mm|
|Work Load Capacity||3,307 lbs||1,500 kg|
|Saw Blade||Blade Size (L x T x W)||11’6″ x 0.042″ x 1-1/4″||3505 x 1.1 x 34 mm|
|Blade Speed||89-295 ft/min Stepless||27-90 m/min Stepless|
|Blade Control||Top Limit Setting||Automatic Setting with Quick Approach Feeler|
|Cutting Control||Hydraulic Pressure & Flow Control Valve|
|Vise Operation||Type||Front Split Vise and Rear Vise|
|Control||Hydraulic Full-Stroke Cylinder|
|Saw Blade||5 HP||3.7 kW|
|Hydraulic Pump||1 HP||0.75 kW|
|Cutting Fluid Pump||1/4 HP||0.12 kW|
|Power Requirement||Power Supply Voltage||AC220V±10%, 3 PH, 60 Hz or AC440V±10%, 3 PH, 60 Hz|
|Cutting Fluid||Tank Capacity||22.5 gal||85 liters|
|Pump Type||Centrifugal Electric Pump|
|Hydraulic||Tank Capacity||7.9 gal||30 liters|
|Pump Type||Variable-Discharge Vane Electric Pump|
|Pump Capacity||4.0 gal/min||15 L/min|
|Pressure Setting||384 psi||2.7 MPa (27 kgf/cm2)|
|Chip Disposal||Chip Conveyor|
|Material Index||Index Mechanism||Shuttle Vise|
|Number of Input Station||1-99|
|Number of Cut-Off Pieces||1-9999|
|Remnant Length||2.24″ Plus Length of Parts||57 mm Plus Length of Parts|
|Machine Dimensions (W x L x H)||Head-Up Position||76.6″ x 93.1″ x 69.8″||1945 x 2366 x 1772 mm|
|Head Down Position||76.6″ x 93.1″ x 50.6″||1945 x 2366 x 1285 mm|
|Table Height||27.6″||700 mm|
|Machine Weight||3,310 lbs||1,500 kg|
Specifications and the machine design may change without notice at the sole discretion of Amada’s Engineering Department.
Contact for repairand recovery of AMADA products and our corporate activities.